Shingle roof coating in Erlanger is a narrow service. We inspect the shingles, decking, and flashing first, then coat only roofs whose tabs still lie flat.
1Inspect The Roof
2Coat The ShinglesCoating suits a narrow band of shingle roofs. If yours looks like the right-hand card, reroofing is the better call.
Before any coat goes on, check whether it would change coverage from the shingle maker on your roof.
Shingle roofs wear first at their details. These five areas get checked and sealed before the field of the roof is coated.
Granule loss and wear run heaviest where two slopes meet and carry water. Worn valleys get repaired or sealed with fabric before coating.
Rubber boots crack long before the shingles fail. Each boot is replaced or sealed and coated with a brushed-in detail.
Flashing where a roof meets a steeple, chimney, or wall is often the oldest metal on the building. Loose pieces are refastened and sealed.
Washed-off granules collect in gutters and clog them, and water backs up under the first course. Gutters are cleared and the drip edge checked.
Ridge caps take the most wind and sun. Cracked or lifted caps get sealed or replaced so the coating has a solid edge.
Coating is one of three paths for a worn commercial shingle roof. The inspection shows which one your roof is on.
| Option | Fits When | Watch For | Next Step |
|---|---|---|---|
| Shingle Coating | Tabs flat, deck firm, one layer | Maker approval for shingles | Recoat when worn |
| Spot Repairs Only | A few damaged tabs or boots | Leaks returning at flashing | Coat later if needed |
| Reroofing | Curled tabs, soft deck, two layers | Permit for the scope | New shingles or metal |
Low-slope sections on the same building often get silicone roof coating during the same visit.
These benefits apply only to shingle roofs that pass the inspection gate above.
A coating over flat, firm shingles adds a protective layer that can push back the date a full reroof is needed.
Coating skips tear-off, disposal, and new underlayment, which tends to cost less than reroofing a church or office.
Gray, tan, or white coatings can be matched to the building, which matters on visible pitched roofs facing a street or parking lot.
Services, office hours, and storefronts carry on below, since the work happens from the roof and ladders.
That is the moment to check the roof. Call us and we will tell you whether coating or reroofing fits what you are seeing.
Five steps, starting with the gate that decides whether a coating fits at all.
We check tab flatness, granule loss, decking from above and below, and the number of layers, then confirm the coating maker approves its product for shingles.
Low-pressure washing removes dirt and loose granules without lifting tabs. Moss and debris come out of the valleys and gutters.
Pipe boots, vents, valleys, and wall flashing get the same detail sealing a metal roof would, with fabric where joints have opened.
The coating is rolled or sprayed in the color you picked, at the thickness on the data sheet, working one slope at a time.
Gutters get cleared of washed-off grit, and a final walk checks every boot, valley, and ridge cap before we leave.
Many shingle buildings have metal or flat sections too. These services cover them.
Many shingle coatings are acrylic-based, and pitched metal sections on the same building can take acrylic in the same visit.
Acrylic roof coating in Erlanger
Churches and offices often have metal garages or canopies beside the shingle roof, and those get the full metal prep.
Metal roof coating in Erlanger
Flat sections behind a pitched shingle roof, where water sits after rain, usually get silicone.
Silicone roof coating in ErlangerAnswers about which shingle roofs qualify, permits, color, and leaks.
Some can. Shingle roofs on churches, offices, and strip centers qualify when the shingles lie flat, hold most of their granules, and sit on firm decking, and when the coating maker approves its product for asphalt shingles.
Curled tabs, missing shingles, or several existing layers rule a roof out. Valleys, pipe boots, and wall flashing get the same detail sealing as metal.
Ask PDS of Kenton County before work starts. Planning and Development Services handles building permits for Erlanger, and scope decides the answer, since a coating differs from tearing off shingles or replacing decking.
A visible color change can also raise a zoning question, because the city's business guide ties zoning permits to exterior changes.
Gray, tan, and white are the common choices, matched to the building. Lighter colors reflect more sunlight, and darker ones hide dirt better on a pitched roof that faces the street.
We bring color charts so you can compare them against the brick, siding, and trim before deciding.
It comes down to roof size, the number of valleys and penetrations, and the weather. Small single-slope offices go faster than steep, cut-up church roofs with steeples and dormers.
We plan the work around services and office hours and share the schedule before the lift arrives.
Only after the leak source is found and repaired. Leaks on shingle roofs usually start at pipe boots, valleys, or wall flashing, and coating over an active leak traps water in the decking.
Once the source is sealed and the deck is dry, the coating protects the repair along with the rest of the roof.
Send the details, or call to describe the shingles and where water is showing up inside.
Leave your name and number and we will call you about your commercial roof.
Or call now: (859) 204-8079